Subjects
To be awarded the PMC20116 Certificate II in Manufactured Mineral Products competency must be achieved in fifteen (15) units of competency: six (6) core units of competency nine (9) elective units of competency from Groups A and B, as specified below. A minimum of two (2) specialist elective units must be chosen from Group A; up to one (1) specialist elective unit may be chosen from Group A of PMC30116 Certificate III in Manufactured Mineral Products The balance of units, to a maximum of seven (7), may be chosen from Group A or Group B to bring the total number of electives to fifteen (15). Up to four (4) of the elective units of competency can be selected from this Training Package; other endorsed Training Packages and accredited courses, where those units are available at Certificate II or III. Note: Where prerequisite units apply, these must be counted in the total number of units required for achievement of the qualification. | ||
Core units of competency | ||
Unit code | Unit title | |
Participate in environmentally sustainable work practices | ||
Work safely | ||
Apply workplace procedures | ||
Clean workplace or equipment | ||
Communicate in the workplace | ||
Select one (1) of the following units. Note that only MSMOPS101 OR PMAOPS101 may be included in this qualification, not both. | ||
Unit code | Unit title | Prerequisites |
Make measurements | ||
Read dials and indicators | ||
Elective units of competency Group A - Specialist electives | ||
Unit code | Unit title | Prerequisites |
Operate equipment | ||
Use enterprise computers or data systems | ||
Monitor process operations | ||
Operate local control system | ||
Operate equipment to blend/mix materials | ||
Operate grinding equipment | ||
Prepare for production | ||
Process greenware/green products | ||
Operate an autoclave | ||
Heat accelerate the curing of precast concrete | ||
Operate crushing equipment | ||
Operate a calcining kiln | ||
Operate slip casting equipment | ||
Operate manual glazing equipment | ||
Prepare materials for clay and ceramic production | ||
Finish products after firing | ||
Hand mould products | ||
Operate a firing kiln | ||
Operate extrusion equipment | ||
Operate pressing equipment | ||
Operate glass melting process | ||
Operate process ovens | ||
Operate blown insulation equipment | ||
Operate float forming equipment | ||
Operate fibre forming equipment | ||
Operate container forming equipment | ||
Operate glass printing equipment | ||
Operate primary annealing equipment | ||
Operate glass finishing equipment | ||
Operate on-line stacking and assembly equipment | ||
Schedule, cut and bend reinforcement | ||
Finish green concrete products | ||
Cast moulded concrete products | ||
Finish cured concrete products | ||
Spin concrete pipes | ||
Conduct benching operations | ||
Assemble, fabricate and place reinforcement | ||
Finish casting operation | ||
Demould concrete products | ||
Batch mix concrete | ||
Deliver concrete to site | ||
Prepare asphalt | ||
Operate forming equipment | ||
Produce fibrous plasterboard | ||
Use and maintain tools and equipment for refractory operations | ||
Prepare for, install and repair refractory brickwork/blockwork | ||
Prepare for and install mouldable refractory materials | ||
Prepare for and cast refractory materials | ||
Prepare for and apply shotcrete for installation | ||
Prepare for, install and repair ceramic fibre | ||
Up to one (1) specialist elective unit may be chosen from Group A of PMC30116 Certificate III in Manufactured Mineral Products. | ||
Group B - Other electives | ||
Unit code | Unit title | Prerequisites |
Conduct local risk control | ||
Apply cost factors to work practices | ||
Interpret product costs in terms of customer requirements | ||
Apply 5S procedures | ||
Monitor process capability | ||
Apply quality standards | ||
Use planning software systems in operations | ||
Undertake root cause analysis | ||
Contribute to the application of a proactive maintenance strategy | ||
Follow emergency response procedures | ||
Use equipment | ||
Work in accordance with an issued permit | ||
Monitor and control work permits | ||
Observe permit work | ||
Enter confined space | ||
Work in a team | ||
Achieve work outcomes | ||
Process and record information | ||
Undertake minor maintenance | ||
Manage conflict at work | ||
Sample and test materials and product | ||
Collect routine site samples | ||
Select and prepare materials | ||
Shift materials safely by hand | ||
Store materials for production | ||
Organise self | ||
Move materials | ||
Operate bulk materials handling equipment | ||
Deliver customer service | ||
Allocate and complete team tasks | ||
Drive medium rigid vehicle | ||
Drive heavy rigid vehicle | ||
Operate a forklift | ||
Note: Only one of TLIC3003 or TLIC3004 may be included in this qualification, not both. Up to four (4) relevant units may be selected from this Training Package, other endorsed Training Packages and accredited courses, where those units are packaged in Certificates II or III. |